ADS-B Out is the transmitting half: your aircraft broadcasts its GPS position, altitude and speed to controllers and nearby traffic, and in most controlled U.S. airspace it is mandatory. ADS-B In is the receiving half: it brings traffic and weather into your cockpit, and no rule requires it. If you are training toward an airline career, you will meet both on your first cross-country, so you should understand exactly what each one does, which one the regulations care about, and where each fits in your preflight and in-flight routine.
The short version for a student pilot: Out is about being seen, In is about seeing. Out is a legal equipment question. In is a situational-awareness question that you will answer once you start flying real cross-countries, and your instructor will teach you how to use it with discipline rather than as a crutch.
TL;DR
- ADS-B Out broadcasts your aircraft’s GPS position, altitude, ground speed and other data about once per second. It is required in Class A, B and C airspace and in several other defined areas under 14 CFR § 91.225.
- ADS-B In receives traffic and weather data in the cockpit. The ADS-B Out rule does not mandate it, and its broadcast services carry no subscription or usage fees.
- Two links exist: 1090ES (1090 MHz) and UAT (978 MHz). Class A airspace requires 1090ES. Weather (FIS-B) arrives only on 978 MHz.
- Information you receive through ADS-B In is for situational awareness only. It never replaces a proper weather briefing or a visual scan.
Table of Contents
- ADS-B Out: your aircraft announces itself
- ADS-B In: your cockpit receives traffic and weather
- ADS-B In vs. Out at a glance
- Where ADS-B Out is required
- Do you need ADS-B In?
- Advanced ADS-B In applications
- What changed recently in the ADS-B Out rule
- Checking coverage on your planned route
- Common mistakes
- Training where this knowledge is part of the course
- Our perspective
- FAQ
- Sources
ADS-B Out: your aircraft announces itself
ADS-B stands for Automatic Dependent Surveillance-Broadcast. “Automatic” means the avionics transmit without a pilot or controller prompting them. “Dependent” means the system relies on an onboard navigation source, normally GPS, to know where the aircraft is.
According to the FAA’s Ins and Outs page, ADS-B Out broadcasts the aircraft’s GPS location, altitude, ground speed and other data to ground stations and other aircraft once per second. The same page notes that traditional radar sweeps for position only every 5 to 12 seconds, which is why controllers see an ADS-B Out aircraft more precisely and more often.
That is the whole function of Out. You are not receiving anything. You are making your aircraft visible to air traffic control and to any other aircraft that carries ADS-B In.
What the equipment consists of
The FAA’s installation guidance states that an ADS-B Out transmitter alone does not satisfy §§ 91.225 and 91.227. An aircraft needs a Version 2 transmitter plus a compatible GPS position source. In practice, that means one of two arrangements:
- A Mode S transponder with Extended Squitter, called 1090ES, operating on 1090 MHz.
- A Universal Access Transceiver, called UAT, operating on 978 MHz.
In a rental or school trainer, this equipment is installed and certified by the owner. Your job as a student is to know how to confirm it is on, set correctly and transmitting, and to know what the rules require of you in the airspace you plan to enter.
ADS-B In: your cockpit receives traffic and weather
ADS-B In is the receiving side. Per the same FAA Ins and Outs page, it delivers weather and traffic position information directly to the cockpit, including graphical weather and text advisories such as NOTAMs and significant weather activity. The FAA stresses that what you receive is for situational awareness only.
Two services matter most.
TIS-B and ADS-R: traffic
TIS-B (Traffic Information Service-Broadcast) shows you aircraft that the ground system sees by radar but that may not be broadcasting ADS-B Out. The FAA’s Benefits page describes TIS-B traffic as covering aircraft in radar contact within a 15-nautical-mile radius and up to 3,500 feet above or below your own position, with altitude, ground track, speed and distance displayed. ADS-R (rebroadcast) passes data between the two links so that a 978 MHz aircraft can see a 1090 MHz aircraft and the other way around.
According to the FAA’s pilot applications page, TIS-B and ADS-R are available at or below 24,000 feet (FL240) and only within coverage of an ADS-B ground station. You also need to be broadcasting valid ADS-B Out to receive TIS-B. That last point is a frequent surprise: In without Out gets you less than you expect.
FIS-B: weather and flight information
FIS-B (Flight Information Service-Broadcast) is the weather feed. The FAA lists the products on the UAT frequency: AIRMETs, SIGMETs, Convective SIGMETs, METARs, TAFs, regional and CONUS NEXRAD radar, NOTAMs, PIREPs, special use airspace status, and winds and temperatures aloft (FAA Ins and Outs).
The NTSB’s ADS-B FAQ adds two practical points: ADS-B In is not mandated by the Out rule, and a voluntary In installation also needs a compatible display. Those same FIS-B and TIS-B broadcast services require no subscription or usage fees.
If METARs and TAFs are new vocabulary, our guide to reading METARs and TAFs covers the formats you will see on that display.
ADS-B In vs. Out at a glance
| ADS-B Out | ADS-B In | |
|---|---|---|
| What it does | Broadcasts your position, altitude, speed | Receives traffic and weather |
| Direction | Aircraft to ground stations and other aircraft | Ground stations and aircraft to your cockpit |
| Required by rule | Yes, in defined airspace (§ 91.225) | No |
| Needs a display | No | Yes, a compatible display or app-connected receiver |
| Frequencies | 1090 MHz (1090ES) or 978 MHz (UAT) | 1090 MHz, 978 MHz or both |
| Weather (FIS-B) | Not applicable | 978 MHz only |
| Main benefit | Controllers and traffic see you | You see traffic and weather |
Where ADS-B Out is required
The text of 14 CFR § 91.225 states that since January 1, 2020, ADS-B Out is required in:
- Class A airspace.
- Class B and Class C airspace.
- Within 30 nautical miles of the Appendix D airports, from the surface up to 10,000 feet MSL.
- Above the ceiling of Class B or C airspace, up to 10,000 feet MSL.
- Class E airspace at and above 10,000 feet MSL over the 48 contiguous states and D.C., excluding airspace at and below 2,500 feet AGL.
- Class E airspace at and above 3,000 feet MSL over the Gulf of Mexico, out to 12 nautical miles from the coast.
Aircraft that were never certificated with an engine-driven electrical system, such as balloons and gliders, have limited exemptions, and ATC may authorize deviations. The FAA’s ADS-B program page confirms that the airspace rule sits in § 91.225 and the equipment performance requirements in § 91.227, and that no FAA authorization is needed to operate with ADS-B Out in that airspace or to use ADS-B In for basic traffic awareness.
In plain terms: if you fly a trainer into a Class B or C airport, or above 10,000 feet MSL, you need working ADS-B Out. The FAA publishes an airspace and coverage map so you can see where the requirement applies; the FAA’s ADS-B FAQ points to it and explains that rebroadcast and traffic services work only within range of a ground station.
Why the frequency choice matters
The two links behave differently, and the FAA FAQ spells out the consequences:
- 1090ES is required in Class A airspace, works in all ADS-B Out required airspace and meets international ADS-B Out requirements. A 1090 MHz In receiver gets ADS-B and TIS-B traffic but cannot receive FIS-B weather.
- UAT (978 MHz) users must keep a transponder and can operate in ADS-B Out required airspace only below FL180 unless they are dual-equipped. UAT also delivers the FIS-B weather.
This is why a piston single flown below 18,000 feet often uses UAT, and why a pilot who wants the airline-style high-altitude, international route eventually works with 1090ES.
Do you need ADS-B In?
Legally, no. Practically, most pilots find it useful once they leave the pattern. Here is how to think about it by stage of training.
Private pilot. You are learning to scan outside, manage radio calls and brief weather from official sources. ADS-B In traffic shows you where to look, but the FAA is explicit that it is for situational awareness, so your eyes and your preflight briefing remain the primary tools. Our guide to obtaining a weather briefing walks through that process.
The FAA’s AC 91-92 encourages pilots to use real-time weather through ADS-B and third-party providers before departure and en route as part of their preflight actions under § 91.103. It describes ADS-B In as available on permanently mounted or handheld receivers, which is why many students connect a portable receiver to a tablet app. We cover that setup in our article on ADS-B and ForeFlight.
Instrument student. In-flight weather becomes more valuable because you are flying in and near clouds and making decisions about routing and alternates. Remember that FIS-B radar is a mosaic with a time delay, so it is a strategic picture, not a tool for threading between cells.
Commercial and multi-engine. Operations are longer, faster and often at higher altitude, where 1090ES and its international acceptance matter. Understanding both links is part of being professional with the equipment you fly.
Current pilots upgrading. If you already hold a certificate and are moving to a more complex aircraft, check which link that aircraft uses before assuming your portable receiver will show you weather. A 1090 MHz-only receiver will not.
Advanced ADS-B In applications
Beyond basic traffic and weather, the FAA’s ADS-B In 101 briefing lists applications such as Surface Traffic Situational Awareness, Traffic Situation Awareness with Alerts (ATAS), CAVS and Interval Management, each tied to a published RTCA standard. The FAA program page notes that advanced operations such as CAVS and In-Trail Procedure require FAA authorization, unlike basic traffic awareness. These are largely airline and operator topics, so you will meet them later in an airline career rather than in a private pilot course.
What changed recently in the ADS-B Out rule
The core airspace requirement has not moved since 2020. The most recent change was an FAA direct final rule published October 17, 2023, effective December 18, 2023, which added TSO-C166c and TSO-C154d as acceptable standards beside TSO-C166b and TSO-C154c. The FAA described it as an additional means of compliance that does not burden operators of existing equipment, so installed Version 2 units remain compliant. A correction published April 29, 2024 fixed cross-reference errors. Always verify the current text of § 91.225 before a flight into unfamiliar airspace.
Checking coverage on your planned route
ADS-B services are ground-station based, so the usable range of your In receiver, and TIS-B and ADS-R in particular, depends on where the stations are. Before a cross-country:
- Open the FAA airspace and coverage map referenced in the FAA ADS-B FAQ and look at your route and altitudes.
- Confirm whether your route enters § 91.225 airspace, which tells you whether Out is required on that leg.
- Identify your link (1090ES or UAT) and what your receiver can display. If you need FIS-B, you need 978 MHz reception.
- Expect gaps at low altitude in mountains or remote areas, and have your official weather briefing complete before you go.
Common mistakes
- Treating ADS-B In as a weather briefing. It supplements a briefing and never replaces one.
- Assuming In works without Out. TIS-B requires you to be broadcasting valid ADS-B Out.
- Expecting FIS-B on a 1090 MHz receiver. Weather comes through 978 MHz.
- Relying on traffic that is not shown. Not every aircraft is equipped, and air-to-air ADS-B is only as complete as the traffic broadcasting.
- Forgetting the transponder rules. A UAT-only aircraft must retain a transponder, and its altitude limit stops at FL180.
Training where this knowledge is part of the course
ADS-B questions turn up on the knowledge test, on the oral portion of a checkride and in every real cross-country. Our Private Pilot Part 141 course teaches the equipment, the airspace rules and the weather sources as parts of one flight-planning routine, and our Airline Career Pilot Program takes you from there through the ratings an airline expects. It is published at $49,950, and our Fixed-Price Airline Flight School Program is published at $85,900.
As a Florida academy with Self Examining Authority, we conduct FAA checkrides in-house, so you are not waiting on an outside examiner’s calendar. International students can enroll with M1 visa support.
If you want to see which program matches your starting point, the flight training courses page lays out each rating.
Our perspective
We teach ADS-B as two separate questions, because pilots who blur them make poor decisions. The first question is regulatory: does this aircraft have compliant ADS-B Out for the airspace I plan to enter? That is a yes-or-no item on your preflight, and it belongs in the same habit as checking the airworthiness paperwork and the transponder.
The second question is about judgment: how much do I trust what ADS-B In shows me? Our answer is that the display is a second set of eyes, never the first. We want students who brief weather from official sources, scan outside and then use the receiver to confirm or refine their picture.
That discipline is what an airline pilot career is built on, and it is why we structure our Part 141 programs around proficiency and check-ride readiness. With in-house checkrides under our Self Examining Authority, we can move a student forward when they are ready, without waiting on an outside examiner. We design our programs for pilots who want to reach the airlines with a clear plan, and who treat equipment knowledge as part of professional airmanship.
Rainer
FAQ
Is ADS-B In required by the FAA?
No. The NTSB’s ADS-B FAQ states that the ADS-B Out rule does not mandate ADS-B In. Only ADS-B Out is required, and only in the airspace described in § 91.225. If you choose to add In, you need a compatible display to see the data.
Can I get ADS-B weather without a subscription?
Yes. The FAA’s FIS-B and TIS-B broadcast services require no subscription or usage fees, according to the NTSB’s ADS-B FAQ. You do need a receiver that handles 978 MHz to get FIS-B weather, and a display such as a panel unit or a tablet app. Remember the weather is for situational awareness and not a replacement for an official briefing.
What is the difference between 1090ES and UAT?
They are the two ADS-B links. 1090ES runs on 1090 MHz, is required in Class A airspace and works in all ADS-B Out airspace. UAT runs on 978 MHz, is limited to operations below FL180 unless the aircraft is dual-equipped, and carries the FIS-B weather broadcast.
Does a transponder alone satisfy the ADS-B Out requirement?
No. The FAA states that a transmitter alone is not enough: the aircraft needs a Version 2 ADS-B Out transmitter and a compatible GPS position source. A Mode S transponder with Extended Squitter can serve as the transmitter, as can a UAT.
Do I need ADS-B In as a student pilot?
Not by regulation. Many students find a portable receiver helpful once they begin cross-country flying, as long as they keep scanning and brief weather from official sources first. Your instructor will show you how to integrate it into your routine.
Sources
- Ins and Outs, FAA
- Installation, FAA
- Benefits, FAA
- ADS-B In Pilot Applications, FAA
- NTSB Technology Panel, ADS-B FAQs
- 14 CFR § 91.225
- FAA ADS-B program page
- FAA Frequently Asked Questions on ADS-B equipage
- FAA ADS-B FAQ
- FAA AC 91-92
- ADS-B In 101 briefing, FAA
- Federal Register direct final rule, October 17, 2023
- Federal Register correction, April 29, 2024